Dentalis T3 Implant

Dentalis T3 is a tapered two-piece implant with dual thread technology, which allows a moderate insertion rate. Its thread design enables vertical condensation of the bone with dual spiral channels and domed apex. This implant features horizontal grooves produced by micro-machining; these horizontal grooves impede epithelial down growth on titanium implants.

Micro threads provide enhanced initial stability and increase contact area to the crestal bone, which promotes osseointegration at the crestal bone level to reduce platform switching.
The Dentalis T3 enables adaptation of the gingival tissues to the abutment, and has become the preferred implants of clinicians worldwide, especially in the case of immediate implant placement after tooth extraction.
With this design, the Dentalis T3 is extremely advantageous, particularly on bone type 4, where primary stability is difficult to achieve. With the BAS™ surface, Dentalis T3 is able to form a strong bond between the implant surface and the surrounding bone.

The Dentalis T3 is a self-drilling, self-tapping product, featuring anatomic design to optimize the bone compaction effect, improve bone density, and provide better primary stability.
The Dentalis T3 is available with diameters of 3.75, 4.2, 4.7, 5 mm, and lengths ranging from 8 to 16mm.

Superior advantages:

  • Platform switching enables good adaptation of the gingival tissues to the abutment and prevents cervical bone resorption.

  • Horizontal grooves produced by micro-machining impedes epithelial down growth on titanium implants.

  • Micro threads provide enhanced initial stability and increases contact area to crestal bone, which will enhance osseointegration at the crestal bone level.

  • Dentalis T3 has Dual thread With his designed Dentalis T3 provide shorten drilling protocols and self condensing bone .

  • Dentalis T3 has Dual spiral channels With his designed Dentalis T3 provide self driling, self tapping and self condensing bone .

  • Dentalis T3 has Doome apex

Dentalis Surface:

Surface roughness is achieved from “grit-blasting,” using a unique combination of the HA particles (soluble) with different sizes of grains. This process creates optimal structural roughness on the surface the surface, and enables the incorporation of biocompatible particles (such as HA and TCP).

Roughness is measured with an average roughness (Ra), while the most commonly used parameter for describing roughness is calculated in microns. The rough surfaces produced by grit-blasting have irregular geometries with Ra value of 3.0 μm, which is considered optimal for the osseointegration process.

Raw Material:

All Dentalis implants are made of Ti 6Al-4V ELI that is a higher-purity (“extra-low interstitial”) version of Ti 6Al-4V, with lower specified limits on iron and the interstitial elements C and O. It is an alpha + beta alloy .Ti 6Al-4V ELI may be considered in any biomedical application, particularly for implantable components, because of its biocompatibility, good fatigue strength, and low modulus. Ti 6Al-4V ELI has been the material of choice due to its excellent biocompatibility. The ELI grade has superior damage tolerance (fracture toughness, fatigue crack growth rate) and better mechanical properties compared to standard grade Ti 6Al-4V.

Implant Range:

Implant Range:

8 mm10 mm11.5 mm13 mm16 mm
3.75 ∅123708123710123711123713123716
4.2 ∅124208124210124211124213124216
5.0 ∅125008125010125011125013125016

Drilling procedure:

  • 3.75 ∅
  • 4.2 ∅
  • 4.7 ∅
  • 5.0 ∅
Recommendation : to reduce the pressure in the bone around the implant neck:
Bone Type D1 use the last drill up to 1/3 depth.
Bone Type D2-3 use the last drill to the depth of the cortex.
Bone Type D4 use the one before last drill desirable to the depth of the cortex
For example:Implant diameter 4.25Ø in soft bone (D4) use the 3.2 Ø drill as a
final drill just for the cortex.

Drill Speed (RPM)900-1200900-1200800-1000500-700400-700400-600400-600
Drill Diameter (mm)∅ 1.8∅ 2∅ 2.5∅ 2.8∅ 3.2∅ 3.6∅ 4.1
Recommendation : to reduce the pressure in the bone around the implant neck:
Bone Type D1 use the last drill up to 1/3 depth.
Bone Type D2-3 use the last drill to the depth of the cortex.
Bone Type D4 use the one before last drill desirable to the
depth of the cortex For example : Implant diameter 3.75Ø in
soft bone (D4) use the 3.2 Ø drill as a final drill just for the cortex.

Drill Speed (RPM)900-1200900-1200800-1000500-700400-700400-600
Drill Diameter (mm)∅ 1.8∅ 2∅ 2.5∅ 2.8∅ 3.2∅ 3.6
Recommendation : to reduce the pressure in the bone around the implant neck:
Bone Type D1 use the last drill up to 1/3 depth.
Bone Type D2-3 use the last drill to the depth of the cortex.
Bone Type D4 use the one before last drill desirable to the depth of the cortex
For example:Implant diameter 4.7Ø in soft bone (D4) use the 4.1 Ø drill as a
final drill just for the cortex.

Drill Speed (RPM)900-1200900-1200800-1000500-700400-700400-600400-600300-500
Drill Diameter (mm)∅ 1.8∅ 2∅ 2.5∅ 2.8∅ 3.2∅ 3.6∅ 4.1∅ 4.6
Recommendation : to reduce the pressure in the bone around the implant neck:
Bone Type D1 use the last drill up to 1/3 depth.
Bone Type D2-3 use the last drill to the depth of the cortex.
Bone Type D4 use the one before last drill desirable to the
depth of the cortex For example : Implant diameter 5.0 Ø in
soft bone (D4) use the 4.6 Ø drill as a final drill just for the cortex.

Drill Speed (RPM)900-1200900-1200800-1000500-700400-700400-600400-600300-500300-500
Drill Diameter (mm)∅ 1.8∅ 2∅ 2.5∅ 2.8∅ 3.2∅ 3.6∅ 4.1∅ 4.6∅ 4.8

Jump to